Industrial Lubricants
Formulated with carefully-selected and refined base oils
They include the state-of-the-art additives that ensure robustness and reliability for all parts of machinery and equipment, even in extreme working conditions.
Industrial Oil Range
MAKER TELEX E
ISO Viscosity grades: 46, 68
These oils are specially designed for use in hydraulic circuits requiring lubricants with marked anti-wear properties. Manufactured from carefully selected bases with specific to notably enhance their properties.
They are specially suitable for hydraulic circuits and civil works machines equipped with any type of pump, particularly working under high pressures and, in general for all kinds of mechanisms requiring stable oils and in those in which the maximum anti-wear levels required by international standards must be attained and exceeded.
MAKER TELEX HVLP
MAKER HYDRAULIC SC
ISO viscosity grades: 46
Top quality oils for hydraulic circuits. Manufactured from paraffinic bases using ashless technology. They include special additives for hydraulic systems with extremely fine tolerance servo-valves where an excellent filterability in the hydraulic fluid is required.
MAKER HYDROFLUX EP
MAKER ARIES TURBO GAS CC
ISO Viscosity grades: 32
Lubricant formulated with hydrocracked bases, specially designed for the lubrication of the latestgeneration gas and combined cycle turbines. Characterised essentially by its exceptional resistance to oxidation, considerably extending its service life. Includes extreme pressure additives, which allow the lubrication of the gearboxes located in the turbine generator shaft.
Lubricant adequate for gas turbines, steam turbines and turbo-compressors that run at high temperatures and require high-performance lubricants. It can be used for the lubrication of ammonia compressors.
MAKER TURBO ARIES
MAKER MERAK VDL
ISO Viscosity grades: 32,46,68
Merak VDL oils belong to the group of oils commonly referred to as compressor oils. Their careful formulation includes, in addition to high-quality base oils, the necessary additives to increase their resistance to oxidation and to ensure good anti-wear and anti-corrosion properties. They are specially recommended for the lubrication of the cylinders and mechanisms of rotary and alternate compressors, whether for air or inert gases, with high discharge temperatures (up to 220 ºC).
MAKER ELECTRA 2X
GENERATOR EXTRA LONG LIFE GAS 4005
Top High Quality state-of-the-art lubricant that is specially designed for stationary gas engines. This product has been developed to attend request of new generation gas engines working with higher pressure and temperature in chamber of combustion, to keep the efficiency and high performance. It is formulated using base oils that are more refined than those conventionally used, together with cutting-edge additives that afford excellent performance in cleanliness engine and deposits reduction. This can avoid valve recession and preignition process in order to protect internal engine components under high load.
REPSOL VESTA AW
REPSOL MAKER TÉRMICO
Top High Quality state-of-the-art lubricant that is specially designed for stationary gas engines. This product has been developed to attend request of new generation gas engines working with higher pressure and temperature in chamber of combustion, to keep the efficiency and high performance. It is formulated using base oils that are more refined than those conventionally used, together with cutting-edge additives that afford excellent performance in cleanliness engine and deposits reduction. This can avoid valve recession and preignition process in order to protect internal engine components under high load.
REPSOL MAKER SYSTEM EP 220
These oils are obtained from carefully selected paraffinic bases to which specific additives are added to endow them with marked extreme pressure and anti-wear properties. Therefore, in addition to having a high viscosity index, these oils are highly resistant to oxidation and have excellent demulsifying capacity, easily attaining load step 10 in the FZG test.
These oils are typically used to lubricate bearings by circulation subject to very severe service conditions, including water contamination, normally used in rolling mills. Their characteristics also make them suitable for lubricating industrial dividers not subject to shock loads, only medium loads. These oils, despite their EP additives, remain innocuous in the presence of metals, for which they can be used to lubricate large-diameter slow-speed plain bearings by means of drip feed, oil bath or oil ring lubrication. In their lowest level of viscosity, these oils are also used to lubricate medium-speed ball or roller bearings.
REPSOL MAKER TAURO
ISO : 68, 100, 150, 220, 320, 460, 680
Tauro range of products have been developed for applications in industrial gear assemblies with high load requirements and harsh environments. Its careful formulation incorporates the highest quality bases and additives, improving its extreme pressure and anti-rust performance, its anti-foaming capacity and its resistance to oxidation. It is suitable for all kinds of industrial gearboxes, bearings and multipliers, using splash or circulating lubrication.
REPSOL CXR COOLANT
Coolant Grade: 30%, 50%
Antifreeze formulated from ethylene glycol and anticorrosive and anti-foam additives. Amine and nitrate free, recommended for all types of diesel and petrol engine cooling circuits. Especially for aluminium and aluminium alloy circuits. Offers good antifreeze, coolant, and metal surface protection properties. Prevents mechanical breakdowns caused by high temperatures by dissipating heat. Recommended for light vehicles.